Boom! Here you are. You are in the right place. This article will give you the tips on how to adjust the water level in toilet tank with ball. You are at home just chilling out, then you realize that your toilet has some issues. The water level is higher or lower than usual.

You call your maintenance guy but he’s held up somewhere else. There’s nobody else in the house so it’s all up to you. Most probably you do not have any knowledge or experience when it comes to toilets and their technicalities. You open the toilet tank to see if you can figure something out but no ideas are forthcoming. Then you decide to look it up online.

The ball also known as a toilet float is a very common water level regulator that balance the water level in the toilet tank. The ball is usually found in older models toilet models but it is still very common. A standard ballock toilet has two valves, the flush and the fill valve. The ball is found on the fill valve and is attached to a steel rod.

The ballock is light enough to enable it to float on water. This characteristic enables it to maintain a common level with the water in the toilet tank. When at the same level the ballock can adjust itself accordingly. If the tank is full the valve closes to ensure no more water flows in. of the tank is empty the valve opens to ensure the flow of water into the tank.

To adjust the level of water in the tank with a ball requires very few simple steps. Before adjusting you’ll need the following:

  • A Ballock
  • Pair of pliers
  • Plumbers tape
  • Screwdriver
  • Vinegar

some steps on How to Adjust Water Level in Toilet Tank with Ball

Identify the Problem

Open the toilet tank. Be very careful with the cover lid if it’s made of ceramic since it can easily break. Check the level of water and the ballock. If the toilet tank is full and the ballock is below the water level then it means that the ballock is spoilt and you’ll have to replace it. Using the pair of pliers remove the float ball out of the rod. Once removed apply plumbers tape to the threads of the steel arm. Take the new ballock and place it in the arms.

If the problem is not with the ballock, worry less, we got you. Empty the tank of all the water. Allow water from the external pipes to flow in. If there is no water or very little water flowing in then it’s probably a blockage within the pipes. Consult your plumber in this case. If not then let’s move on to the next step

Turn off the water supply

Using the external valve that is most likely outside the toilet, close the water supply. Empty the toilet tank by flashing it. Since the water supply is closed the toilet tank will not be refilled. This will prevent any distractions and make your work easier.

Check for any valve defects

As mentioned earlier there are two valves in a ballock toilet, the flush valve and the fill valve. The flash valve controls the flow in the process of water into the toilet tank. The fill valve on the other hand controls the level of water in the tank. Do a proper check of these two valves. If you notice any visible damage on either valves, then it is recommended that you call a plumber or technician to check it out. This is because valves are pretty technical and can get damaged if not handled with care.

Analyze the height of the ballock

The height of the ballock is a good indicator of water levels. It can indicate if the water level is higher or lower than the standard level. You can fix this problem easily using a pair of pliers. If the ballock level is pretty low you can perform two operations.

Once, you can twist the screw clockwise to adjust it. Secondly, you can bend the screw upwards to fix it. If the water level is high you can do the opposite of the lower case. One, you can tune the screw anticlockwise. Two, you can bend the steel rod downwards. You can also check if the ballock contains water. If yes then change the ballock. Check the adjustments on the valves to ensure it is properly attached.

Test if it's working

Reopen the source of water and allow it the toilet tank. If the water level looks good then your problem is fixed. If the problem is not fixed then repeat the above steps.

Related Links

Leave a Reply

Abdul Kader

Hello, I am Abdul Kader, a professional blogger with an experience of five years. I have writing blogs on different topics for more than five years. I have wide arrays of blog on various niches. However, I enjoy working on baby, ride-on toys, drone, home improvement, health, life-style, tech etc. niches. In my free time, I love to travel to different places and watching soccer.
shares